We have payments for Western union, MoneyGram , Bitcoin and Bank Wire ( Sigue,Golden Crown and RIA )
Member
Customer Care
Contact
Price List
Testosterone Recipes
Boldenone Recipes
Nandrolone Recipes
Trenbolone Recipes
super mix recipes
Masteron Recipes
Primobolan Recipes
Growing Muscle Recipes
Sex Female hormone Recipes
I Cooked Oils
Steroid News

Trestolone Acetate MENT Powder Conversion Recipe

  • Trestolone Acetate 500ml @50mg/ml
  • 25g trest ace powder,
  • 378ml GSO(Grapeseed oil),
  • 10ml 2% BA(benzyl alcohol),
  • 90ml 18% BB(benzyl benzoate).

20 mL solution that has a 50 mg/mL
-1 gram Trestolone Acetate Powder
-16.55 ml_ Grape Seed Oil (GSO)
-0.6 mL Benzyl Alcohol
-2 mL Benzyl Benzoate

 
This will achieve a 20 mL solution that has a 50 mg/mL ratio. The 16.55 mL of GSO is calculated 
based on a 0.85 mL displacement of Trestolone when dissolved. This means that 1 gram of Trest 
will only take up about 0.85 mL of space. The BA/BB ratio is 3/10. 

To make more than 1 gram at a time, simply multiply the amounts by how much you want to do. 
For example, this guide will demonstrate making 3 grams at one time. The following recipe is used 

-3 grams Trestolone Acetate Powder 

-49.65 mL Grape Seed Oil 

-1.8 mL Benzyl Alcohol 

-6 mL Benzyl Benzoate 


What you will need: 


-Trestolone Powder 
-Grape Seed Oil 

*You can buy multiple types, I prefer bulk GSO that I can filter myself as shown in the picture 
-Benzyl Alcohol 
-Benzyl Benzoate 

-Empty Vials, sealed and sterile (20mL recommended) 
-Large (20mL+) syringe 
-Regular (3mL) syringe 

-A few large gauge needles (21-18ga recommended) 
-Sterile .45u Whatman syringe filter 
-Unsterile .45u Whatman syringe filter 

*You can buy pre-filtered GSO from research companies. This filter isn't necessary if you go that route 
-A couple small class jars/beakers to hold your solution 

*Try to stay close to the volume that you are making, jars that seal are ideal 
-A large pot/container that can hold hot water and your smaller jar 
-Alcohol prep pads 

-Paper towels or similar, mainly for cleaning 


Getting started 

Make sure your work area is clean. You aren't going to perform surgery, but you don't want excessive dirt. 

Wipe your empty mixing jars/beakers with an alcohol prep pad, rinse with water, and dry with a paper towel. 

Add Trest Powder to one and set to the side. Add some GSO to the other, 
exceeding the amount needed for your brew. In this case, we need 49.65 mL, so 
use about 60 mL. Place the GSO jar in the larger container and add hot water to 
the larger container (NOT THE GSO). This will heat up the GSO for easier filtering. 


After heating up, use the larger syringe to draw out some GSO. 
Screw on the unsterile Whatman filter and start filtering into the 
jar with the Trest powder. 

This step may take a few times to finish. For us, we need about 
50 mL. The syringe used is 
25mL. So, we draw in 25 
mL, attach the Whatman, 
filter, unscrew the 
Whatman, draw in another 
25 mL, reattach the 
Whatman, and filter the 
rest. You just need to filter 
the total needed for the 
recipe. 

Using the normal syringe, 
measure out the 
appropriate amounts of 
the Benzyl Alcohol and 
Benzyl Benzoate. 


At this point, you should have something that looks like mud. This is 
normal. The Trest is floating around and not much dissolving has 
happened. Seal off the jar, I use a screw top. 


Like we did with the GSO, place the Trest/GSO/BA/BB solution into a 
bath of hot water to heat it up. You will need to shake up the container 
to help the dissolving process. Trest powder likes to fall to the bottom 
and clump. Repeat as many times and needed to dissolve most of the 
trest. 



Once most of the Trest dissolves, you'll have a cloudy dark yellow/orange solution left. You don't want solid 
particles floating around. Keep the solution hot. 

Grab the large syringe and draw into it enough solution to fill a vial. You may want to pull a little extra on the first 
vial because the Whatman can hold a full mL itself. Attach the Sterile Whatman filter and slip on a large gauge 
needle. 



Grab a sterile vial, wipe the top with 
an alcohol pad, and insert a large 
gauge needle into the top, off 
center at an angle. This is the 
venting needle to let out air as you 
filter in the Trest. 

Insert the needle from the syringe 
into the vial across from the venting 
needle, at an opposite angle. 

Filter. 

This stage will take some patience, 
because the filter will start catching 
all the bad stuff you don't want in 
the solution. There will be a good 
bit of resistance, just keep at it. 
Keep the extra solution hot, it 
makes filtering easier. 

Repeat for all the vials. 



Congratulations, you made Trest Ace. 


Links:electric water heatertankless water heater electric
Message Us